Ampacity in a sentence
Synonym: conductivity.
Meaning: The maximum amount of electric current a conductor can carry.
(1) Ampacity ratings are typically given in amperes or milliamperes.
(2) The ampacity of the cable was too low, so we had to run a new line.
(3) The ampacity of a wire can be affected by the length of the circuit.
(4) The ampacity rating of the cable was clearly marked on the packaging.
(5) The ampacity of a wire can be affected by voltage drop considerations.
(6) Ampacity is an essential concept in electrical engineering and design.
(7) Ampacity ratings are determined through rigorous testing and analysis.
(8) We tested the ampacity of the circuit, and then we added more outlets.
(9) The ampacity of the cable was insufficient to power the new equipment.
(10) The ampacity of the cable was exceeded, and then the insulation melted.
Ampacity sentence
(11) The ampacity of a wire determines its maximum current-carrying capacity.
(12) The ampacity rating of a cable is typically indicated on its insulation.
(13) Ampacity calculations are based on the wire's ability to dissipate heat.
(14) The ampacity of the transformer was not enough, so we had to upgrade it.
(15) We calculated the ampacity of the circuit, and then we added a subpanel.
(16) We tested the ampacity of the transformer, and then we adjusted the taps.
(17) Higher gauge wires generally have a lower ampacity than lower gauge wires.
(18) The ampacity of the wire determines its maximum current-carrying capacity.
(19) The electrician used a clamp meter to measure the ampacity of the circuit.
(20) Ampacity is an important factor in preventing electrical fires and hazards.
Ampacity make sentence
(21) Ampacity is a fundamental concept in electrical safety and code compliance.
(22) The ampacity of the conductor was too low, so we had to use a larger gauge.
(23) The ampacity of a wire can be increased by using larger diameter conductors.
(24) The ampacity of the conductor was exceeded, and then the circuit overheated.
(25) The ampacity of the cable was reduced by the presence of other nearby wires.
(26) The ampacity of the cable was exceeded when too many devices were plugged in.
(27) Ampacity is a crucial consideration in the selection of electrical conductors.
(28) We increased the ampacity of the circuit, but the breaker still kept tripping.
(29) We measured the ampacity of the wire, and then we calculated the voltage drop.
(30) The ampacity of the wire was not sufficient, so we had to parallel two cables.
Sentence of ampacity
(31) The inspector checked the ampacity of the wiring during the safety inspection.
(32) The ampacity of the fuse must be matched to the current rating of the circuit.
(33) The ampacity of a wire can be influenced by the presence of nearby heat sources.
(34) Ampacity is a critical factor to consider when sizing circuit breakers and fuses.
(35) The ampacity of a wire can be reduced if it is exposed to corrosive environments.
(36) The ampacity of a wire can be affected by the presence of nearby magnetic fields.
(37) We measured the ampacity of the cable, and then we installed a voltage regulator.
(38) The ampacity of the wire was not sufficient for the load, so we had to replace it.
(39) The ampacity of a wire can be affected by the type and thickness of its insulation.
(40) The electrician checked the ampacity of the wires, and then he installed a new panel.
Ampacity meaningful sentence
(41) The electrician checked the ampacity of the circuit before installing the new outlet.
(42) The electrician tested the ampacity of the circuit after making repairs to the wiring.
(43) It is important to consider the ampacity of a circuit when designing electrical systems.
(44) It is crucial to select wires with an appropriate ampacity for the intended application.
(45) The ampacity of a wire can be influenced by the ambient temperature of its surroundings.
(46) We checked the ampacity of the breaker, and then we replaced it with a higher rated one.
(47) The electrician recommended upgrading the wiring to increase the ampacity of the system.
(48) The ampacity of the conductor must be sufficient to handle the load without overheating.
(49) The electrician recommended using a thicker wire to increase the ampacity of the circuit.
(50) The ampacity of a wire can be reduced if it is subject to excessive bending or stretching.
Ampacity sentence examples
(51) The engineer calculated the ampacity of the power line based on its diameter and material.
(52) Ampacity tables are commonly used to determine the maximum current a wire can safely carry.
(53) The National Electrical Code provides guidelines for determining the ampacity of conductors.
(54) Ampacity ratings should always be followed to ensure the safe operation of electrical systems.
(55) The ampacity of a conductor can be affected by factors such as temperature and insulation type.
(56) Although the ampacity of the wire was high, the circuit still failed due to a faulty connection.
(57) The manufacturer provided a chart showing the ampacity of their cables at different temperatures.
(58) The engineer designed the system with a margin of safety to ensure the ampacity was not exceeded.
(59) Ampacity calculations are necessary to ensure the safety and efficiency of electrical installations.
(60) The ampacity of a wire should always be higher than the expected current load to prevent overheating.
Sentence with ampacity
(61) The electrician explained that the ampacity of the wire decreases as the length of the run increases.
(62) The ampacity of the conductor was affected by the ambient temperature and the presence of insulation.
(63) The electrician recommended using a circuit breaker with a higher ampacity rating to prevent tripping.
(64) The electrician explained that the ampacity of the wire was reduced when it was installed in a conduit.
(65) The electrician installed a fuse with a lower ampacity to protect a sensitive component in the circuit.
(66) The inspector noted that the ampacity of the circuit breaker was too low for the load it was protecting.
(67) The engineer calculated the ampacity of the conductor based on the maximum current it could safely carry.
(68) The designer specified a cable with a higher ampacity to compensate for voltage drop over long distances.
(69) The inspector checked the ampacity of the circuit using a clamp meter to ensure that it was not overloaded.
(70) The electrician recommended increasing the ampacity of the circuit, which would require upgrading the wiring.
Use ampacity in a sentence
(71) The electrician recommended using a voltage drop calculator to determine the appropriate ampacity for the circuit.
(72) The designer chose a cable with a higher ampacity to ensure that it could handle any future upgrades to the system.
(73) The manufacturer recommended using a cable with a higher ampacity for applications where the current could fluctuate.
(74) The electrician tested the ampacity of the wire using a specialized tool to ensure it was within the acceptable range.
(75) Although the ampacity of the wire was high, the circuit breaker tripped due to a short circuit, and the power went out.
(76) It is important to regularly inspect and maintain electrical systems to ensure the ampacity of wires is not compromised.
(77) The electrician tested the ampacity of the circuit breaker, and he found that it was faulty, so he replaced it with a new one.
(78) The manufacturer's specifications listed the ampacity of the cable, but it was important to also consider the ambient temperature.
(79) The engineer designed the system with a margin of safety, ensuring that the ampacity of the components exceeded the expected load.
(80) The electrician explained that the ampacity of the wire could be affected by the length of the run and the type of insulation used.
Sentence using ampacity
(81) The electrician recommended using a cable with a lower ampacity for applications where the current was limited to prevent overheating.
(82) The electrician checked the ampacity of the cable, and he found that it was insufficient for the load, so he recommended upgrading it.
(83) The technician tested the ampacity of the circuit, and he discovered that it was fluctuating due to a faulty connection, so he repaired it.
(84) The inspector checked the ampacity of the electrical panel, and he found that it was overloaded, so he recommended adding a subpanel to distribute the load.
(85) The contractor installed a high-ampacity transformer to power the industrial equipment, and he also installed a surge protector to protect against power surges.
(86) The electrician explained to the homeowner that the ampacity of the wiring in their old house was inadequate for modern appliances, and he suggested rewiring the entire house.
(87) The engineer designed the electrical system with a high ampacity to ensure that it could handle the maximum load, but he also included a backup generator in case of a power outage.
(88) The engineer calculated the ampacity of the electrical system based on the expected load, and he designed it with redundancy to ensure that it would not fail in case of a component failure.
(89) The electrician measured the ampacity of the wire, and he determined that it was sufficient for the load, but he also checked the voltage drop to ensure that it was within acceptable limits.
Ampacity meaning
Ampacity is a term used in electrical engineering to describe the maximum amount of electrical current that a conductor can carry without overheating or causing damage. It is an important concept to understand when designing and installing electrical systems, as exceeding the ampacity of a conductor can lead to safety hazards and equipment failure. Here are some tips for using the word "ampacity" in a sentence:
1. Define the term: Before using the word "ampacity" in a sentence, it is important to understand what it means. You can define it as the maximum current-carrying capacity of a conductor, measured in amperes. Example: The electrician calculated the ampacity of the wire to ensure it could safely carry the required current.
2. Use it in context: When using the word "ampacity" in a sentence, it is important to provide context so that the reader or listener understands what you are referring to. This can be done by including information about the electrical system or equipment being discussed. Example: The ampacity of the circuit breaker was exceeded, causing it to trip and shut off power to the building.
3. Be precise: When discussing electrical systems, precision is key. Use the word "ampacity" instead of more general terms like "capacity" or "load" to ensure that you are accurately conveying the maximum current-carrying capacity of a conductor. Example: The engineer specified a wire with an ampacity of 20 amps to ensure it could handle the load of the equipment.
4. Use it in technical writing: Ampacity is a technical term used in electrical engineering, so it is appropriate to use it in technical writing such as reports, specifications, and manuals. Example: The installation manual provided guidelines for selecting wires with the appropriate ampacity for the system.
5. Use it in conversation: While ampacity is a technical term, it can also be used in conversation with others who are familiar with electrical systems. Using technical terms can help to convey information more precisely and efficiently. Example: The electrician and engineer discussed the ampacity of the wires to ensure the system was designed to handle the required current.
In conclusion, ampacity is an important concept in electrical engineering that describes the maximum current-carrying capacity of a conductor. When using the word "ampacity" in a sentence, it is important to define the term, provide context, be precise, use it in technical writing, and use it in conversation with others who are familiar with electrical systems. By following these tips, you can effectively communicate information about ampacity and ensure the safety and reliability of electrical systems.
The word usage examples above have been gathered from various sources to reflect current and historical usage of the word Ampacity. They do not represent the opinions of TranslateEN.com.